This is a 5V 4-Channel Relay interface board, be able to control various appliances, and other equipment’s with large current. It can be controlled directly by Micro-controller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
Operating Voltage: 5V DC, Channel: 4 channel, Relay Output Max.: AC250V 10A or DC 30V 10A, Input: Active Low,.
|
2A Full Wave Bridge Rectifier Power Supply PCB With Copper Pour.
Components Required: Diode 1N5408 (4pcs), Capacitor 2200uF, 3300uF Or 4700uF (1pc), Capacitor 100nF - 100V (1pc), LED 5mm Red (1pc), Resistor 0.5W 1.5K (1pc), 2 Way PCB Terminal Block (1pc), 4 Way Multi-color Red+Black PCB Terminal Block (1pc). Note: You can change the components according to your requirement..
|
2A Full Wave Bridge Rectifier Power Supply with Switch PCB.
Size: 1.9"x2.9" (49mm x 74mm). Components Required: Diode 1N5408 (4pcs), Capacitor 4700uF - 35V (1pc), Capacitor 100nF - 100V (1pc), LED 5mm Red (1pc), Resistor 0.25W 1.5K (1pc), 2 Way PCB Terminal Block (2pc), SPDT 3A Switch (1pc). Note: You can change the components according to your requirement..
|
5A Full Wave Bridge Rectifier Power Supply PCB.
Size: 2.9"x3.9" (74mm x 99mm), Track Width: 3mm, Copper Pour Clearances: 1.5mm, Mounting Hole: 4 x 3mm. Components Required: Diode 6A4 (4pcs), Capacitor 4700uF - 50V (2pc), Capacitor 100nF - 100V (1pc), LED 5mm Red (1pc), Resistor 0.5W 3.9K (1pc), 2 Way PCB Terminal Block (1pc), 4 Way Multi-color Red+Black PCB Terminal Block (1pc). Note: 1.) You can change the components according to your requirement. 2.) You can select available option to Print Your Name on PCB..
|
Size: 5.2" x 2.9" (132mm x 74mm)
Load: AC Max. 1000W Input: AC 220V-250V 50Hz.
|
Automatic Water Level Controller PCB
Size: 2.9" x 5.1"..
|
2A Full Wave Bridge Rectifier Power Supply PCB Print Out on Toner Transfer Paper.
Components Required: Diode 1N5408 (4pcs), Capacitor 2200uF, 3300uF Or 4700uF (1pc), Capacitor 100nF - 100V (1pc), LED 5mm Red (1pc), Resistor 0.5W 1.5K (1pc), 2 Way PCB Terminal Block (1pc), 4 Way Multi-color Red+Black PCB Terminal Block (1pc), Blank PCB 2x3 (1pc). Note: You can change the components according to your requirement..
|
Over Load and Short Circuit Protection Circuit PCB Only.
Protecting your layout from short circuits and overloads is essential to prevent damage to equipment. Components List for this PCB: ( Show More ) .
|
AND Gate Using Switch, LED And Diode On Breadboard
AND Gate Project: AND Gate Using LED And Diode on Dot Matrix PCB.
|
Assembled Unregulated Power Supply - Full Wave Bridge Rectifier
This kit is a quick, neat, and inexpensive way to provide a smoothed 3V to 36V, 1A to 8A (Depending on transformer & components), unregulated DC power supply suitable for powering many electronics circuits. It only requires the AC output of a transformer (not supplied). Input: Green for transformer connection, Output: 2 x Red Positive and 2 x Black Negative Components Used: PCB (2.9"x3.9"), Diode, LED 5mm, 2.7K 0.5W CFR Resistor, Electrolytic Capacitor, Vishay 100nF 250V Polyester Film Capacitor, 2 Way PCB Terminal Block etc. Note: You can customized this Assembled Kit by selecting capacitor and diodes from Available Options..
|
2 Transistors 2-LEDs Flasher On Breadboard
PCB of this Project: Transistors LED Flasher PCB.
|
Over Load and Short Circuit Protection Circuit PCB Only with Copper Pour.
Protecting your layout from short circuits and overloads is essential to prevent damage to equipment. Components List for this PCB: ( Show More ) .
|
Center Tapped Transformer Full Wave Rectifier Power Supply PCB (Copper Pour) with Toner Transferred, Ready for Etching.
Components Required: Diode 1N4007 (2pcs), Capacitor 2200uF (1pc), Capacitor 100nF (1pc), LED 5mm (1pc), Resistor 0.5W 1.5K (1pc), 3 Way PCB Terminal Block (1pc), 4 Way Multi-color Red+Black PCB Terminal Block (1pc). Note: 1.) You can change the components according to your requirement. 2.) You can select available option to Print Your Name on PCB..
|
Center Tapped Transformer Full Wave Rectifier Power Supply PCB.
Size: 1.9"x2.9" (49mm x 74mm), Track Width: 2mm, Copper Pour Clearances: 1.5mm, Mounting Hole: 4 x 3mm. Components Required: Diode 1N4007 (2pcs), Capacitor 2200uF (1pc), Capacitor 100nF (1pc), LED 5mm (1pc), Resistor 0.5W 1.5K (1pc), 3 Way PCB Terminal Block (1pc), 4 Way Multi-color Red+Black PCB Terminal Block (1pc). Note: 1.) You can change the components according to your requirement. 2.) You can select available option to Print Your Name on PCB..
|
Over Load and Short Circuit Protection Circuit PCB with all components soldering on it.
Protecting your layout from short circuits and overloads is essential to prevent damage to equipment. Components List Used In This Project: ( Show More ) .
|
Showing 16 to 30 of 54 (4 Pages)