Assembled Full Working Project
LEDs And Diode Based AND Gate Circuit on Dot Matrix General Purpose PCB. Components Used: Switches, LED's, Resistors, Diode, Connector, Battery, Dot-Matrix PCB etc. Project Content: Assembled Project PCB - 1pc, Battery Cable - 1pc and 9V Battery - 1pc. Project On Breadboard: AND Gate Using LED And Diode on Breadboard.
|
2 Transistors 2-LEDs Flasher PCB Print Out on Toner Transfer Paper.
Components Required: Diode 1N4007 (1pc), Capacitor 22uF 63V (2pcs), LED 5mm Red (1pc), LED 5mm Green (1pc), Resistor 0.25W 18K (2pc), Resistor 0.25W 470 Ohm (2pc), Transistors BC547 (2pcs), Variable Resistor (Preset) 10K (1pc), Relimate 2-pin Male Header 5.08mm (1pc), Blank PCB 2x3 (1pc), Working Voltage: 5 to 9V DC. Note: 1.) You can change the components according to your requirement. 2.) You can select available option to Print Your Name on PCB..
|
This is a 5V 1-Channel Relay interface board, be able to control various appliances, and other equipment’s with large current. It can be controlled directly by Micro-controller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
Operating Voltage: 5V DC, Channel: 1 channel, Relay Output Max.: AC250V 10A or DC 30V 10A..
|
IR Infrared Obstacle Sensor Module PCB - LM358
Components Required: IC LM358 (1pc), IR Emitter (1pc), IR Receiver (1pc), LED 5mm Red (1pc), Resistor 0.25W 1.5K, 22K & 180 Ohm (1pc each), 3-Pin Relimate Male Header (1pc), Small Preset 20K (1pc). Note: You can change the components according to your requirement..
|
IR Infrared Obstacle Sensor Module PCB - LM358 - Print Out on Toner Transfer Paper.
Components Required: IC LM358 (1pc), IR Emitter (1pc), IR Receiver (1pc), LED 5mm Red (1pc), Resistor 0.25W 1.5K, 22K & 180 Ohm (1pc each), 3-Pin Relimate Male Header (1pc), Small Preset 20K (1pc), Blank PCB 1x2 (1pc). Note: You can change the components according to your requirement. .
|
OR Gate Using Switch, LED And Diodes On Breadboard
OR Gate Project: OR Gate Using Diode on Dot Matrix PCB.
|
This RS232 circuit can be used to interface a microntroller to a PC via a RS232 connection (serial port). This circuit converts signals between RS232 voltage levels and TTL voltage levels. It is bi-directional, where TTL signals are converted to RS232 levels and RS232 levels are converted to TTL levels. The circuit can be assembled with any MAX232 compatible RS-232 Transmitter/Receiver chip..
|
Assembled 1A Regulated Power Supply - Full Wave Bridge Rectifier and 7805
This kit is a quick, neat, and inexpensive way to provide a smoothed 5V, 1A regulated DC power supply suitable for powering many electronics circuits. It only requires the AC output of a transformer (not supplied). Input: 6V to 12V AC (Green for transformer connection), Output: 5V DC Max. 1A (2 x Red Positive and 2 x Black Negative) Components Used: PCB (2.9"x3.9"), Diode, Fixed Voltage Regulator, LEDs, Resistors, Electrolytic Capacitor, Polyester Film Capacitor, PCB Terminal Block, Heatsink etc. Note: You can customized this Assembled Kit by selecting capacitor and diodes from Available Options..
|
AND Gate PCB Using Diodes
Size: 1.9"x2.9" (49mm x 74mm).
|
2A Full Wave Bridge Rectifier Power Supply PCB (Copper Pour) Print Out on Toner Transfer Paper.
Components Required: Diode 1N5408 (4pcs), Capacitor 2200uF, 3300uF Or 4700uF (1pc), Capacitor 100nF - 100V (1pc), LED 5mm Red (1pc), Resistor 0.5W 1.5K (1pc), 2 Way PCB Terminal Block (1pc), 4 Way Multi-color Red+Black PCB Terminal Block (1pc), Blank PCB 2x3 (1pc). Note: You can change the components according to your requirement..
|
2A Full Wave Bridge Rectifier Power Supply PCB (Copper Pour) with Toner Transferred, Ready for Etching.
Components Required: Diode 1N5408 (4pcs), Capacitor 2200uF, 3300uF Or 4700uF (1pc), Capacitor 100nF - 100V (1pc), LED 5mm Red (1pc), Resistor 0.5W 1.5K (1pc), 2 Way PCB Terminal Block (1pc), 4 Way Multi-color Red+Black PCB Terminal Block (1pc). Note: You can change the components according to your requirement..
|
Assembled Unregulated Power Supply - Full Wave Bridge Rectifier
This kit is a quick, neat, and inexpensive way to provide a smoothed 3V to 36V, 1A to 5A (Depending on transformer voltage & components), unregulated DC power supply suitable for powering many electronics circuits. It only requires the AC output of a transformer (not supplied). Input: Green for transformer connection, Output: 2 x Red Positive and 2 x Black Negative Components Used: PCB (1.9"x2.9"), Diode, LED 5mm, 1.5K 0.5W CFR Resistor, Electrolytic Capacitor, Vishay 100nF 250V Polyester Film Capacitor, 2 Way PCB Terminal Block etc. Note: You can customized this Assembled Kit by selecting capacitor and diodes from Available Options..
|
2 Transistors 2-LEDs Flasher PCB (Copper Pour) with Toner Transferred, Ready for Etching.
Components Required: Diode 1N4007 (1pc), Capacitor 22uF 63V (2pcs), LED 5mm Red (1pc), LED 5mm Green (1pc), Resistor 0.25W 18K (2pc), Resistor 0.25W 470 Ohm (2pc), Transistors BC547 (2pcs), Variable Resistor (Preset) 10K (1pc), Relimate 2-pin Male Header 5.08mm (1pc), Working Voltage: 5 to 9V DC. Note: 1.) You can change the components according to your requirement. 2.) You can select available option to Print Your Name on PCB..
|
.
|
2 Transistors 6-LEDs Flasher PCB Only.
Note: 1.) You can change the components according to your requirement. 2.) You can select available option to Print Your Name on PCB..
|
Showing 1 to 15 of 54 (4 Pages)